Understand the knowledge of fiber optic quick fast connector
Everyone is familiar with the term optical fiber, but many people have never heard of fiber optic quick fast connector. This article focuses on how to use the fiber optic quick fast connector. Everyone is familiar with the term optical fiber, but many people have never heard of fiber optic quick fast connector. This indispensable component in optical fiber transmission lines and optical fiber distribution frames has stumped many people. This article focuses on how to use the fiber optic quick fast connector.
What is an fiber optic quick fast connector?
The fiber optic quick fast connector is also used as a live joint, which can be used to connect the continuous optical path formed by two optical fibers. The optical device can be reused many times, and it is faster and more convenient to use. If divided by structure, there are mechanical connection type and There are two types of hot-melt type, and the continuous type includes two types: embedded and straight-through.
How to use fiber optic quick fast connector?
The optical fiber quick connector mainly includes three parts: the main body, the shell and the tail cap as shown in the figure. The editor here reminds everyone to be careful not to discard the packaging bag after taking out the above-mentioned objects from the packaging bag, as the packaging bag will be used later.
1. Insert the leather fiber optic cable through the tail cap, and use scissors to peel off the outer skin of the leather fiber optic cable by about 5 to 6 cm. Then cut off the peeled skin, keeping the skin layers on both sides flush. Be careful during the stripping process to prevent damage to the internal optical fiber cable.
2. Put the optical cable in the clamp, keep the edge of the outer skin flush with the scribe line in the clamp, then close the clamp cover, and then use Miller pliers to close to the edge of the clamp, cut off the exposed coating layer, and expose the optical fiber. Then clean the exposed white fiber with alcohol.
3. Use a clamp to cut the optical fiber. After cutting, take the optical cable out of the clamp and compare it with the icon on the product packaging bag. Then align the optical fiber with the main body hole and insert it, and stop when the primary reaches the bottom of the main body. At this time, you can clearly observe the bending state of the optical fiber. Press the white crimping cover on the main body to the bottom, and then screw the tail cap on On the main body, buckle the shell again.
What is an fiber optic quick fast connector?
The fiber optic quick fast connector is also used as a live joint, which can be used to connect the continuous optical path formed by two optical fibers. The optical device can be reused many times, and it is faster and more convenient to use. If divided by structure, there are mechanical connection type and There are two types of hot-melt type, and the continuous type includes two types: embedded and straight-through.
How to use fiber optic quick fast connector?
The optical fiber quick connector mainly includes three parts: the main body, the shell and the tail cap as shown in the figure. The editor here reminds everyone to be careful not to discard the packaging bag after taking out the above-mentioned objects from the packaging bag, as the packaging bag will be used later.
1. Insert the leather fiber optic cable through the tail cap, and use scissors to peel off the outer skin of the leather fiber optic cable by about 5 to 6 cm. Then cut off the peeled skin, keeping the skin layers on both sides flush. Be careful during the stripping process to prevent damage to the internal optical fiber cable.
2. Put the optical cable in the clamp, keep the edge of the outer skin flush with the scribe line in the clamp, then close the clamp cover, and then use Miller pliers to close to the edge of the clamp, cut off the exposed coating layer, and expose the optical fiber. Then clean the exposed white fiber with alcohol.
3. Use a clamp to cut the optical fiber. After cutting, take the optical cable out of the clamp and compare it with the icon on the product packaging bag. Then align the optical fiber with the main body hole and insert it, and stop when the primary reaches the bottom of the main body. At this time, you can clearly observe the bending state of the optical fiber. Press the white crimping cover on the main body to the bottom, and then screw the tail cap on On the main body, buckle the shell again.
.jpg?imageView2/1/w/300/h/200)
